欧美一区视频,国产婷婷综合网,欧美手机在线观看

BYD clamp forklift charging process picture-

Generally, there are two specifications for the truck: the wide one is 685MM in width, the fork length is about 1200, and the general pallet size is 1200*1200mm; the narrow one is 550MM, the fork length is 1100MM, and the applicable pallet is 1000*1000

Energy saving and environmental protection, simple and convenient operation

(10) The forklift is steered by the rear wheels, so you must always pay attention to the swing of the rear wheel to avoid turning too sharply, which is common among beginner drivers

The gantry is hinged on the front axle support body and consists of a set of parallel steel frames and a sliding bracket for fixing the fork

Its smart handle integrates all switch buttons in the best reach position for easy operation

In this case, the forklift must have good anti-slip capabilities

Full Chinese display instrument: The advanced Chinese display instrument can display the operating status of the vehicle in real time, provide vehicle fault alarms and prompts, and intelligently provide the most accurate real-time information for operation and maintenance personnel, realizing personalized operation functions

It is not the case that cheap ones are good and expensive ones are profiteering; nor is it the case that cheap ones are of poor quality and expensive ones are perfect

The following BYD forklift editor will introduce it step by step

When the battery is arranged on the rear axle, the maintenance of the motor and hydraulic pump is more convenient, because after removing the battery and the pedal, the motor and hydraulic pump are clearly visible

Forklift drivers, please note: (1) Before moving the vehicle, make sure there are no people in front, behind, or around the vehicle, especially if there are obstacles around; (2) When driving, do not exceed the speed limit, slow down when turning, and point to confirm; (3) It is strictly prohibited to use shelves, material frames, etc

Therefore, it is easy to make mistakes when you have to twist your neck to check the reversing road conditions

Freight is also very convenient, the body is agile, and most importantly, it is very environmentally friendly

BYD clamp forklift charging process picture-

This move also helped Anhui Heli achieve continuous improvement in the company's gross profit margin

On the basis of primer spraying, the iron plate of the body can be sprayed with a low-temperature rust-resistant protective layer to cope with the huge temperature difference in the storage operation

The DC motor and hydraulic motor drive the lifting of the fork, pushing the cylinder up and down to lift the fork and goods

High safety factor All mechanical material equipment must make progress in safety design, otherwise it will be difficult to develop in the long run

The oil pump is excessively worn, causing internal leakage of the equipment, and needs to be replaced

com's "2022-2028 China Forklift Market In-depth Research and Investment Prospect Analysis Report"

The fork deflection detection error shall not be higher than the maximum design deflection of the fork

BYD forklifts still perform well in cold chain logistics and have huge room for market expansion

The common tonnage of electric pallet trucks is 1

If the temperature is significantly lower than -15℃, the engine system cannot be operated immediately after starting, but the engine should be run at 1000-1100r/min for 10-15min, and the transmission should be in a neutral position

If the battery is not used for a long time, it should be recharged in time (2) Turn the key switch to the on position

High-quality electronic control system is responsive and easy to control

Under the general trend of "energy saving and environmental protection", specialization, automation, intelligence and new energy technologies have become major opportunities for the development of the forklift industry

Electric transport truck: 1

BYD clamp forklift charging process picture-

Slow driving function: put the handle in a nearly vertical state, and the driving speed will automatically decrease, making it easier to achieve accurate operation in narrow spaces

We can also see some in daily scenes

Otherwise, it is easy to damage the ground and forklift wheels, and it will cause accidents such as cargo collapse, damage to buildings and injuries to personnel

won the gold award in the parts category for its high-performance electric industrial vehicle integrated drive key technology research and development, Fanji Technology (Suzhou) Co Disadvantages: Manual transport trucks rely on human power to pull, which consumes manpower, requires effort when the ground is uneven, and has low transport efficiency The hydraulic synchronization solution described in this article can be applied to the design of forklifts with double telescopic gantry structures

When a vehicle breaks down in the cold storage, it must be moved out of the cold storage as soon as possible and repaired in the buffer zone or maintenance area

The electric transport truck manufacturer is a long-established comprehensive manufacturer with small profits but quick turnover and perfect services Generally, it is one year or 1,000 hours (whichever comes first)

Anti-accidental safety switch The operator faces the fork and the direction of the cargo

The staff who heard the abnormal noise did not take the corresponding emergency measures in time, resulting in the shaft being scrapped The forks of a battery truck are usually raised to a height of 200 MM, which is just enough to lift the pallet off the ground and keep a distance from the ground, allowing for free movement

久久久久黄色_国产91一区_久久99国产精品_欧美一区二_成人黄色在线视频_欧美一级黄色网

New energy forklift leader

Product

BYD Counterbalanced forklift

BYD Warehouse Forklift

BYD large tonnage forklift

BYD tractor truck

Core Features

High security

high performance

High efficiency

High Match

Low overall cost

Super fast charging

Ultra-long life

No charging room required

About Us

Product

BYD Forklift

Contact Info